How to crochet mountain poppy flower
To crochet the mountain poppy it is necessary to prepare the petal section, the pistil, the bud and the leaf.
Necessary: cotton number 10 and number 20 - 1.0 mm crochet needle - 0.45 mm galvanized iron wire - scissors - plasticized iron wire - pliers - cotton.
For leaves use cotton number 10, for everything else number 20.
Explanation of the petal section
Start 5 chains and close them in a circle.
1st round: 10 single crochets.
2nd round: 2 double crochets in a stitch 5 times. Turn the job.
3rd round: 2 double crochet, 2 double crochet in one stitch 6 times, 2 double crochet. Turn the job.
4th round: 2 treble crochets, 5 double treble crochets, 3 double treble crochets in one point twice, 5 double treble crochets, 2 treble crochets. Turn the job.
5th round: 2 double crochets, 7 double high crochets, 3 double high crochet in one point twice, 7 double high crochet, 2 double crochet.
Go down with satin stitches until the round of 10 low stitches and make another petal the same.
Make 2 sections for each flower.
Model with your hands.
Explanation of the pistil
Start 4 chains and in the first make 13 double crochets (total 14). Every 2 stitches form a 2-chain disk.
Cut a piece of plasticized iron wire of the correct length and thickness for the job to be done. At one end, wrap some cotton (the same shade that was used for the pistil) to create a ball. Bend the tip 2 times to block the cotton (with the help of pliers).
Insert the pistil and the two petal sections into the stem, alternating their position. Cover the stem with cotton by working the chains around it, except for about 3 cm that will be inserted into the vase.
Explanation of the outbreak
Start 4 chains and in the first make 9 double crochets (total 10).
1st round: 10 treble crochets.
2nd round: 2 double crochets closed together throughout the round. Cut a piece of plasticized wire to the proper length. At one end wrap a little cotton. Bend the tip 2 times to block the cotton and create a ball. Insert it into the bud and close the second round.
3rd round: 2-3 slip stitches.
Cover the stem with cotton by working the chains around it, except for about 3 cm that will be inserted into the vase.
Explanation of the sheet
Start 25 chains.
Cut a piece of galvanized iron wire that goes around the complete circle of the chains plus another 3 cm on each side. Insert it by working around 24 single crochets on one side and 24 single crochets on the other.
1st round: 3 slip points. 1 slip stitch, 8 chain stitches and in these make: 2 single crochets, 2 medium double crochets, 3 single crochets, 1 slip stitch. Repeat the same 2 times. 1 slip stitch, 6 chain stitches and in these make: 1 single crochet, 2 medium double crochets, 2 double crochets, 1 slip stitch. 3 slip points. 1 slip stitch, 6 chain stitches and in these do: 1 single crochet, 2 half double crochet, 2 double crochet, 1 slip stitch. 2 slip points. 1 slip stitch, 4 chain stitches and in these make: 1 single crochet, 1 half double crochet, 1 single crochet, 1 slip stitch. In a single stitch, make: 1 single crochet, 1 double crochet, 1 double crochet, 1 double crochet, 1 double crochet, 1 single double crochet, 1 single crochet. Repeat the same as on the other side in reverse, then start with 1 slip stitch, 4 chain stitches and in these make: 1 single crochet, 1 half double crochet, 1 single crochet,
Stretch the sheet well, shaping it with your hands. Twist the remaining wire on itself to get a small stem that will be used to insert the leaf into the vase.
Make all the sheets you need for your composition.
Arrange the flowers with some buds in the center of the vase and around the leaves.
Model everything with your hands.
As always I hope I have been clear in the explanation and have given you an extra idea.
Hello everyone to the next creation.
0 Comments
If you have any doubts, please let me know